Epson G3 Series Manuel d'utilisateur télécharger pdf (Page 42)

Setup & Operation 3. Environments and Installation

32 G3 Rev.1

When the Manipulator is a Cleanroom-model, be aware of the followings.

For the Manipulator of Cleanroom-model, use it with an exhaust system.

For details, refer to Setup & Operation: 2.4 Specifications.

CAUTION

■

When operating the Manipulator under special environmental conditions (adverse

conditions with dust and oily smoke), do not place the controller in the same

condition since the controller does not comply with IP54 / IP65. Doing so may

cause equipment damage to and/or malfunction of the controller.

Cable Connections

Connect the power connector and signal connector of the M/C cables to the Controller.

Power Connector

Signal Connector

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 91 92

G3 series 1
Manipulator Manual 3
FOREWORD 4
WARRANTY 4
TRADEMARKS 5
INQUIRIES 5
SERVICE CENTER 5
MANUFACTURER & SUPPLIER 6
SUPPLIERS 6
Before Reading This Manual 7
TABLE OF CONTENTS 9
Maintenance 10
Setup & Operation 11
1. Safety 13
1.3 Operation Safety 15
1.4 Emergency Stop 16
1.6 Manipulator Labels 18
2. Specifications 20
2.3.1 Table Top Mounting 22
G3 Rev.1 13 23
G3 Rev.1 15 25
2.3.2 Multiple Mounting 26
G3 Rev.1 17 27
Upper bellows 28
Plate cover 28
(For Anti-static) 28
Exhaust port 28
Lower bellows 28
G3-301CM G3-351CM 29
2.4 Specifications 30
2.5 How to Set the Model 32
3.2 Base Table 34
3.3 Mounting Dimensions 35
G3-301S/C 36
G3-251S/C 36
Standard -R -L 36
G3-351S/C 36
Center of Joint #3 37
Maximum space 37
3.5 Installation Procedure 39
3.6 Connecting the Cables 41
Cable Connections 42
Power Connector 42
Signal Connector 42
DA-15PF-N (Solder type) 43
3.8 Relocation and Storage 45
Wire tie 47
Example of Arm 47
Retaining Posture 47
4. Setting of End Effectors 48
4.3.1 Weight Setting 50
Weight setting 51
4.3.2 Inertia Setting 52
Rotation center 53
G3 Rev.1 54
G3 Rev.1 45 55
5. Motion Range 56
0 pulse 59
Upper limit: 0 pulse 60
Joint #1 Mechanical Stops 62
Joint #2 Mechanical Stops 63
Measure 65
5.4 Standard Motion Range 67
Center of Joint#3 68
Motion range 68
Base mounting face 68
(°: degree) 69
64 G3 Rev.1 74
1. Safety Maintenance 77
2. General Maintenance 78
2.2 Inspection Point 79
2.3 Greasing 80
2.5 Matching Origins 81
2.6.1 Table Top Mounting 82
2.6.2 Multiple Mounting 83
3. Covers 84
3.1 Arm Top Cover 85
4-M4×12 86
Arm top cover 86
3.2 Arm Bottom Cover 87
3.3 Arm Cap 87
Connector plate 88
Connector sub plate 89
Truss: 4-M4×8 89
Truss: 4-M4 90
Base bottom cove 90
4. Maintenance Parts List 91
4.2.1 S: Standard-model 92
4.2.2 C: Cleanroom-model 92

Commentaires sur ces manuels

Pas de commentaire

Epson G3 Series Manuel d'utilisateur Page 42

Commentaires sur ces manuels

Produits connexes et manuels pour Robotique Epson G3 Series