Epson DM-D210 Manuel d'installation

Customer DisplayDM-D210Installation Manual//// 設置マニュアル / 安裝手冊401285101English

82. Attach the base to the setting position on the IR series, and secure it with the screws.Note:When attaching the base, note that the corners of the

9English5. Connect the cable for the DM-D210 to the DM connector on the IR series.Attaching to the TM-H5000II/TM-J8000The DM-D210 can be attached dire

10Assembling steps1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert

11English3. Pass the cable for the DM-D210 through the base.4. Insert the tab on the base into the hole on the support until you feel it click.5. Conn

12Attaching to the TM-U375/TM-U950The DM-D210 can be attached directly to the TM-U375/TM-U950 printers using the “DM-D pole unit for TM printers (Type

13EnglishAssembling steps1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension,

143. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below.4. Connect the cable for the DM

15English6. Store any excess cable in the support, and attach the DM-D210 to fixing plate A.Attaching to the TM-H6000/TM-U675The DM-D210 can be attach

16Assembling steps1. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert

17English4. Pass the cable for the DM-D210 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Connect the cable fo

CAUTIONS❏ This document shall apply only to the product(s) identified herein.❏ No part of this document may be reproduced, stored in a retrieval syste

187. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of t

19EnglishNote:The paper roll cover may not open if the position of the display is inappropriate. Before securing the position of the display, make sur

20Attaching to Other TM PrintersWhen using with other TM printers, the DM-D210 can be attached to a desk or other surface, using the “DM-D pole unit f

21English2. Pass the cable for the DM-D210 through support C, and attach support C to the DM-D210. When using support B for extension, insert the tab

225. Store any excess cable in the support, and attach the DM-D210 to fixing plate A.6. Peel off the Velcro tapes, and attach the display to the setti

23EnglishAttaching to the DM-D standThe DM-D210 can be attached directly to the DM-D stand using the “DM-D stand unit for DM Customer Display ” (DP-21

24Connectors for the DM-D standThe connectors for the DM-D stand are as follows:Note:The DM-D stand comes with inch-type hexagonal lock screws install

25EnglishJumper settingSet the jumpers on the DM-D stand as follows:The jumpers are located as follows:Precautions on using the power supply unitTo av

26Assembling steps1. Pass the cable for the DM-D210 through the DM-D stand.When extending the length of the DM-D stand, attach the extension support t

27English3. Connect the cable for the DM-D210 to the display connector on the DM-D stand until you feel it click.4. Connect one end of the computer in

1EnglishSafety PrecautionsThis document presents important information intended to ensure safe and effective use of this product. Please read this doc

285. When using as a stand alone, go to step 6.When using with the printer, connect one end of the printer interface cable for the printer to the prin

29English7. Connect the DC cable of the power supply unit (with the arrow mark up) to the power supply unit connector indicated with “POWER IN” on the

30Part Names and FunctionsExterior❏Display: Characters are displayed.❏Power switch: The power is turned on/off.❏DIP switch: The functions of the DM-D2

31EnglishDIP SwitchDIP Switch FunctionsThe DM-D210 has one DIP switch. The functions of the DIP switche are as follows:DIP switch 1(*)This function ca

32Setting the DIP switchesCAUTION:Turn off the DM-D210 while removing the DIP switch cover to prevent electrical damage to the DM-D210.1. Turn off the

33EnglishTurning and Tilting the DM-D210You can turn or tilt the display while holding the support. The display can be moved easily, so do not move an

34Self TestThe DM-D210 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch.Check Items of Self

35EnglishSpecificationGeneral Specifications❏Height, Width, Depth and Weight260mm38mm158mm110mm83mm260mm503mm<DM-D210 and DM-D stand>DM-D Stand(

36•DM-D210:Height: 91 mmWidth: 260 mmDepth: 50.5 mmWeight: 600 g• DM-D stand (DP-501):Height: 53 mmWidth: 260 mmDepth: 110 mmWeight: 385 gDM-D pole un

37English• Base and support A of the “DM-D pole unit for IR” (DP-504):Height: 129 mmWidth: 50 mmDepth: 53 mmWeight: 60 g• Base and support C of the “D

2CAUTION:❏Do not plug the cable differently from the instruction in this manual. Wrong connection may cause equipment damage and fire.❏Be sure to set

38Electrical Specifications❏Type PS-170, PA-6508, PB-6509, PB-6510, PA-6511, PA-6513 (when using the DM-D stand)❏Rated voltage DC 11.4 to 48 V❏Rated c

39EnglishCharacter Specifications❏Type of character• Alphanumeric characters: 95• International characters: 37• Extended graphics: 128 characters ×

40❏

3EnglishWARNINGYou are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate

4ContentsAbout This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Contents .

5EnglishThis manual explains how to set up the DM-D210.UnpackingThe following items are in the box.Make sure that you have all the items shown above,

6UsageThe DM-D210 can be used with the following equiment.❏IR series. You can attach the DM-D210 to the IR series using the “DM-D pole unit for IR” (D

7EnglishAssemblingAttaching to the IR seriesThe DM-D210 can be attached directly to the IR series using the “DM-D pole unit for IR” (DP-504).Required