Epson Equity 386/25 Manuel d'utilisateur Page 55
- Page / 296
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Setting the Real-time Clock
The real-time clock in your Equity 386/25 constantly tracks the
time and date-even when the computer is turned off. The first
time you run the Setup program, you use the Real-time
clock option to set the time and date for your computer. You
may need to use this option again later to adjust the time for
daylight savings time. The computer automatically changes the
date for leap years.
Follow these steps to set the real-time clock:
1.
At the main Setup menu, highlight Real-time
clock . If the time and date have been previously set, the
current settings appear:
If the time and date are correct, you can skip the rest of this
section.
If the time and date are incorrect, go to step 2 below.
If the time and date have never been set, the submenu
contains a template for you to fill in:
Go to step 2 to enter the time and date.
Running the Setup Program
2-19
- User’s Guide 3
- IMPORTANT SAFETY INSTRUCTIONS 5
- Contents 7
- Installing Options 10
- 10
- Troubleshooting 10
- Power-on Diagnostics 11
- Performing System Diagnostics 11
- Disk Change Check 12
- Hard Disk Drive Types 13
- Specifications 13
- Introduction 14
- How to Use This Manual 16
- Where to Get Help 18
- Setting Up Your System 19
- Choosing a Location 22
- Connecting a Monitor 23
- Using the Parallel Interface 26
- Using the Serial Interface 29
- Using the Mouse Connector 30
- Connecting the Power Cord 31
- Connecting the Keyboard 32
- Turning On the Computer 34
- 1-18 Setting Up Your System 36
- Running the Setup Program 37
- Automatic Configuration 38
- Starting the Setup Program 39
- Moving the Cursor Block 43
- Setting the Power-on Password 48
- Power-on password already in 49
- Do not enable the Auto 53
- Setting the Real-time Clock 55
- Running the 57
- Setup Program 60
- 47 to 57) 61
- Setup Program 61
- Reviewing Your Settings 65
- Leaving the Setup Menu 67
- Using the Equity 386/25 68
- Using a Power-on Password 69
- Changing a Power-on Password 70
- Deleting a Power-on Password 71
- Locking the Computer 72
- Selecting the Operating Speed 73
- Controlling the Volume 74
- Equity 386/25 75
- Stopping a Command or Program 77
- Resetting the Computer 77
- Using Disks and Disk Drives 82
- How Disks Store Data 83
- Types of Diskette Drives 85
- Write-protecting Diskettes 91
- Making Backup Copies 92
- Using a Single Diskette Drive 93
- Using Two Diskette Drives 94
- Using a Hard Disk Drive 95
- Backing up the hard disk 96
- Turning Off the Computer 97
- Chapter 4 98
- Starting MS-DOS 99
- Using Drive Designators 100
- The Current Drive 101
- Types of MS-DOS Commands 102
- Entering an MS-DOS Command 104
- Setting the Date and Time 105
- Creating and Managing Files 106
- Copying Files 108
- COPY at the MS-DOS 108
- COPY A:REPORT B: 108
- COPY A:REPORT B:FACTS 108
- COPY REPORT FACTS 109
- COPY A:*.* B: 109
- COPY A:MEMO? B: 109
- Renaming Files 111
- RENAME PROSPECT CLIENT 111
- REN HAMMERS WRENCHES 111
- REN C:*.NEW *.OLD 111
- REN MEMO? MEMO?.OLD 111
- Deleting Files 112
- Using Dir 113
- Your Equity 386/25 114
- The Current Directory 116
- Using Pathnames 117
- \DOS tells MS-DOS to move 117
- (A : , for example) as well 118
- Formatting Diskettes 124
- Using the FORMAT Command 125
- Backing Up Data 127
- Using the DISKCOPY Command 128
- Using the BACKUP Command 131
- The MS-DOS Shell Program 132
- Using the Epson HELP Program 132
- Using the Epson MENU Program 134
- MENU Program Options 136
- Using an AUTOEXEC.BAT File 137
- Creating an AUTOEXEC.BAT File 138
- Using Memory Beyond 640KB 144
- Using EMM386.SYS 146
- Your Equity 386-25 148
- Adding Memory Modules 150
- Possible SIMM configurations 151
- Installing Options 5-3 151
- Installing Option Cards 153
- Removing the Cover 154
- Installing an Option Card 157
- Removing an Option Card 162
- Replacing the Cover 163
- Post-installation Setup 164
- Appendix A 166
- Changing Jumper Settings 167
- * Factory setting 168
- Changing DIP Switch Settings 171
- DIP Switch Settings 173
- Removing the SPF Card 174
- Setting the DIP Switches 176
- Setting the SPF Card Jumpers 177
- Replacing the SPF Card 179
- The Computer Won’t Start 181
- The Computer Locks Up 182
- Password Problems 183
- Removing a Password 184
- Setting a New Password 186
- Keyboard Problems 187
- Monitor Problems 188
- Diskette Problems 190
- Troubleshooting B-13 192
- Diskette Drive Problems 193
- Hard Disk Problems 193
- COPY A:COMMAND.COM C: 194
- A : to log onto 194
- Software Problems 196
- Printer Problems 198
- B-20 Troubleshooting 199
- Option Card Problems 200
- B-22 Troubleshooting 201
- C-2 Power-on Diagnostics 203
- Power-on Diagnostics C-3 204
- Starting System Diagnostics 207
- Selecting an Option 208
- Modifying the Device List 209
- Selecting a Test 211
- 2. You see this 212
- Resuming From an Error 213
- System Board Check 214
- Memory Check 215
- Keyboard Check 216
- ESC and then Enter 217
- Monochrome Adapter Check 218
- Attribute Check 219
- Character Set Check 219
- Video Check 220
- Sync Check 220
- Run All Above Checks 220
- Color Graphics Adapter Check 221
- 40-column Character Set Check 223
- 320x200 Graphics Mode Check 224
- 640x200 Graphics Mode Check 225
- Screen Paging Check 226
- Light Pen Check 227
- Color Video Check 228
- Sequential Seek Check 230
- Random Seek Check 231
- Write, Read Check 231
- Math Coprocessor Check 233
- Alternate Parallel Port Check 234
- Performing System 236
- Alternate Serial Port Check 237
- Dot-matrix Printer Check 237
- Seek Check 239
- Error Codes and Messages 243
- Appendix E 246
- Choosing the Type of Format 247
- Reformatting a Used Disk 248
- Formatting a New Disk 249
- Option 1, Format 250
- (l-16) : 251
- D = Delete 252
- Enter command : 252
- Formatting the Disk 254
- Enter to return to 258
- O-Exit 258
- F-2 Hard Disk Drive Types 260
- Controllers 263
- Interfaces 263
- Power Supply 264
- Mass Storage 264
- Keyboard 265
- Environmental Requirements 265
- Physical Characteristics 265
- Glossary 266
- Ctrl and press 269
- 4 Glossary 269
- See Operating system 279
- 14 Glossary 279
- Glossary 15 280
- Interface and 283
- 20 Glossary 285
- Copying 288
- Epson America, Inc 296
- 2780 Lomita Boulevard 296
- Torrance, CA 90505 296
Produits connexes et manuels pour Manuels des logiciels Epson Equity 386/25
Manuels des logiciels Epson FX-80 Spécifications
(268 pages)
(268 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.874 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels