Epson AcuLaser C2000 Guide d'installation

Where to Find InformationSetup Guide (this manual)Provides you with information on how to place the printer,assembling the printer’s parts and install

Safety Instructions7Important:The wires in the mains lead fitted to this appliance are colouredin accordance with the following code:Green and yellow—

8Removing the Protective Materials2Removing the Protective MaterialsBefore you start the printer, remove all protective materials asshown in the illus

Removing the Protective Materials943

10Finding a Place for the Printer3Finding a Place for the PrinterAllow adequate space for easy operation and maintenance asshown below.Additional spac

Finding a Place for the Printer11Always follow the precautions below when finding a place tolocate the printer:❏ Place the printer where you can easil

12Assembling the Printer4Assembling the PrinterInstalling the Developer CartridgesHandling precautions:❏ When handling the developer cartridges, alway

Assembling the Printer132. Check the color that appears in the cartridge installationwindow.3. Shake well.YellowMagentaBlackCyancartridgeinstallation

14Assembling the Printer4. Slide the developer cartridge in the slot until it clicks.5. Press the green button, then turn the knob counterclockwiseunt

Assembling the Printer15Installing the Photoconductor Unit and WasteToner CollectorHandling precautions:❏ When installing the photoconductor unit, avo

16Assembling the Printer2. Turn the large lever counterclockwise to an upright position.3. Take the photoconductor unit out of its package. Do notremo

Setup GuideColor Laser Printer1 Safety Instructions ...12 Removing the Protective Materials . . 83 Finding a Place for the Printer . . .

Assembling the Printer174. Slide the unit into the slot making sure that the bottom of theunit slides onto the guide rails.Note:Make sure that the uni

18Assembling the Printer6. Turn the large lever clockwise, until the lever rests on thephotoconductor unit.7. Attach the waste toner collector.

Assembling the Printer198. Close the front cover.Installing the Fuser Oil RollHandling precautions:❏ Do not touch the white roll surface.❏ Ifoilgetson

20Assembling the Printer1. Push the lever and lift the printer’stopcover.2. Make sure that the two fuser oil roll levers are in the positionshown belo

Assembling the Printer213. Install the fuser oil roll.4. Turnthetwoleversoutsothattheyrestontopoftheroll.5. Gently close the top cover until it clicks

22Installing the Options5Installing the OptionsIf you purchased any options with the printer, install them beforeplugging in the printer. To install t

Installing the Options232. Remove the cover from the back of the printer, as shown.3. Hold the Hard Disk Drive so that the electrical connector ison t

24Installing the Options4. Secure the drive with the screws provided. cCaution:Do not remove any modules from the circuit board.Otherwise, the printer

Installing the Options25To confirm that the Hard Disk Drive is installed correctly, print astatus sheet. If the drive is not listed on the status shee

26Installing the Options cCaution:Before you install a memory module, be sure to discharge anystatic electricity by touching a grounded piece of metal

iiAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form or by any means, mechani

Installing the Options274. Push one end of the DIMM into the slot until the clip comesup.5. Push the other end of the DIMM into the slot until the cli

28Installing the OptionsTo confirm that the memory module is installed correctly, print astatus sheet. If the total amount of memory listed does not i

Installing the Options292. Remove the cover from the back of the printer.3. Insert the module all the way into slot A in the orientationshown below. T

30Installing the Options4. Replace the cover.To confirm that the ROM module is installed correctly, print astatus sheet. If the module is not listed o

Installing the Options31Installing an Interface CardYour printer comes with a Type B interface slot. Various optionalinterface cards are available to

32Installing the Options3. Slide the interface card into the slot firmly, making sure thatthe connector at the back of the interface card is fully ins

Testing and Connecting the Printer336Testing and Connecting the PrinterPlugging in the Printer1. Make sure that you have the correct power cord for yo

34Testing and Connecting the PrinterFor Testing the PrinterLoading paperFan a stack of A4 or Letter size paper, then tap it on a flat surfaceto even t

Testing and Connecting the Printer35Connecting to the ComputerTo connect your computer to the printer’sbuilt-inparallelinterface, you need a shielded,

36Installing the Printer Driver7Installing the Printer DriverWhen you install the printer driver, the following are installed.❏ Printer driverThe prin

Safety Instructions11Safety InstructionsLaser Printer PrecautionsThis printer uses laser technology. Follow the precautions belowcarefully to ensure s

Installing the Printer Driver37For Windows UsersInsert the CD-ROM that comes with your printer into your CD-ROM drive. Then follow the on-screen instr

38Installing the Printer DriverFor Macintosh UsersYour Macintosh must meet the following requirements to use thedriver included with the printer:Mac O

Installing the Printer Driver39Selecting your printer in the ChooserAfter you have installed the printer driver, you need to open theChooser to select

40To Know More About Your Printer8To Know More About Your PrinterOnline guidesReference Guide❏ How to use the printer❏ How to solve the problems❏ How

2000 NovemberEPSON OVERSEAS MARKETING LOCATIONSEpson America, Inc.3840 Kilroy Airport WayLong Beach, CA 90806Phone: (562) 981-3840Fax: (562) 290-522

2Safety InstructionsImportant Safety InstructionsRead all of the following instructions before operating yourprinter:❏ The printer weighs about 39.5 k

Safety Instructions3❏ Slots and openings, located on the sides of the printer, areprovided for ventilation. Keep these slots and openings clearto allo

4Safety Instructions❏ If you plan to use the printer in Germany, observe thefollowing:To provide adequate short-circuit protection and over-current pr

Safety Instructions5CDRH regulationsFor information about the Center for Devices and RadiologicalHealth of the U.S. Food and Drug Administration, see

6Safety Instructions❏ Not blown directly into the user’sface❏ Vented directly out of the building whenever possibleFor United Kingdom UsersThe EPSON A