Epson EMP-TW200 Guide d'installation

EPrinted in China40466240003.09-.XA(C01)

8Basic Image Quality AdjustmentsSelecting the Color ModeSelecting the Image AspectSelecting the Image AspectSelecting the Color ModeDefault settingWhe

9Basic Image Quality AdjustmentsBasic Image Quality AdjustmentsSqueezeNormalZoomThroughThe images are projected onto the screen with the input signal

10Advanced Color AdjustmentsThe projector allows you to select the optimum colour settings for the images being projected by selecting the appropriate

11Advanced Color AdjustmentsBasic Image Quality AdjustmentsBrightnessInput signalWhen adjusted to + sideWhen adjusted to – sideBrightnessInput signalW

12Viewing images at a preset image quality (memory function)After menu commands such as "Picture Quality" and "Color Adjustment" h

13Viewing images at a preset image quality (memory function)Basic Image Quality AdjustmentsThe Cinema Color Editor program can also be used to store a

14Configuration Menu FunctionsThe configuration menus can be used to make a variety of adjustments and settings involving the screen, image quality an

15Configuration Menu FunctionsConfiguration MenuResolutionSleep ModeLanguageThe message text will be displayed in red when it is time to replace the l

16Configuration Menu Functions"Image" menuThese settings can be adjusted if the output level from the connected equipment is weak and the im

17Configuration Menu FunctionsConfiguration Menu"Color Adjustment" cannot be selected when the colour mode is set to "sRGB".•Color

About The Manuals and Notations UsedTypes of ManualThe documentation for your EPSON projector is divided into the following four manuals. Refer to the

18Configuration Menu Functions"Setting" menu(Setting is only possible when 525i or 625i component video signals are being input)• OFF :IP c

19Configuration Menu FunctionsConfiguration MenuIf aspect is set to "Zoom" when viewing images with subtitles, change the setting as follow

20Configuration Menu FunctionsThis turns the trigger function on and off to determine whether the projector's power on/off status and problems wi

21Configuration Menu FunctionsConfiguration MenuThis sets whether the start-up screen (the image that is projected when projection starts) is displaye

22Configuration Menu Functions"Reset" menuThis initialises the lamp operating time. When this command is selected, the cumulative operating

23Configuration Menu FunctionsConfiguration MenuUsing the Configuration MenusDisplaying a menuSelecting a menu itemUse and to select a menu item,

24Preparation for Using Cinema Color EditorInstalling Cinema Color EditorIf any other applications are open, close them before installing Cinema Color

25Preparation for Using Cinema Color EditorAdjusting projected images using a computer Uninstalling Cinema Color EditorIf you no longer require Cinema

26Using Cinema Color EditorThe following information describes how to use the Windows edition of the program. The Macintosh edition works in basically

27Using Cinema Color EditorAdjusting projected images using a computerSaving adjustments/Loading adjustments from a fileClick a button to carry out th

1Configuration MenuAppendix TroubleshootingAdjusting projected images using a computerBasic Image Quality AdjustmentsContentsFeatures of the Projector

28Using Cinema Color EditorSaving customised settings into memorySaving/loading memory settings and editing memory area namesSaving customised setting

29Using Cinema Color EditorAdjusting projected images using a computerryMake the desired adjustments.Select the memory area to be used.The following t

30Problem SolvingReading the IndicatorsThe projector is provided with the following two indicators which notify you of the operating status of the pro

31Problem SolvingTroubleshootingWhen the Indicators Provide No HelpIf any of the following problems occur and the indicators do not offer a solution,

32Problem Solving The message "Not Supported." is displayed The message "No Signal." is displayedWere the projector and computer c

33Problem SolvingTroubleshooting Images are fuzzy or out of focus Interference or distortion appear in images Image is truncated (large) or smallHas t

34Problem Solving Image colours are not right Images appear darkHas the "Position" setting been adjusted correctly?Use the "Position&qu

35Problem SolvingTroubleshooting Projection stops automaticallyProblems when projection starts Power does not turn onProblems with the remote control

36MaintenanceThis section describes maintenance tasks such as cleaning the projector and replacing consumable parts.CleaningYou should clean the proje

37MaintenanceAppendixConsumable Replacement PeriodsAir Filter Replacement PeriodIf the air filter becomes broken or too dirty to cleanReplace with an

2Features of the ProjectorThe optimum images for the location can be projected simply by selecting the desired colour mode from the following five pre

38MaintenanceReplacing ConsumablesReplacing the Air FilterReplacing the LampResetting the Lamp Operating TimeTurn off the power, wait for the cool-dow

39MaintenanceAppendixRemove the old air filter.Install the air filter cover.Make sure that it faces the correct way.Insert the new air filter.Place yo

40Optional AccessoriesThe following optional accessories are available for purchase if required. This list of optional accessories is current as of Oc

41AppendixList of Supported Monitor DisplaysDepending on the setting, the output screen resolution will change slightly.Component VideoComposite Video

42Specifications* The USB connector is not guaranteed to operate correctly with all USB-compatible devices.Product nameHome Projector EMP-TW200Dimensi

43SpecificationsAppendixCompatible computers for using Cinema Color EditorSafetyUSAUL1950 3rd EditionCanadaCSA C22.2 No.950-95 (cUL)European Community

44SpecificationsWe :EPSON AMERICA, INC.Located at : 3840 Kilroy Airport Way MS: 313 Long Beach, CA 90806Tel : 562-290-5254Declare under sole respon

45AppendixGlossaryFollowing is an explanation of some of the terms used in this guide which may be unfamiliar or which were not explained in the manua

46GlossarySECAMAn abbreviation for Sequential Couleur A Memoire, and a format for ground-based analogue colour television broadcasts. This format is u

47AppendixIndex"SG" stands for Setup Guide.Adjusting the color hue and saturation ...26Advanced...

3Features of the ProjectorEquipped with a wide-angle lens shift functionWide range of brightness adjustmentsA variety of image setting functionsElectr

TW200-E.book Page 48 Monday, September 1, 2003 5:19 PM

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electron

EPrinted in China40466240003.09-.XA(C01)

4Part names and FunctionsFront/TopControl Panel••••Front adjustable feet Setup GuideExtend to adjust the projection angle so that the projector is hor

5Part names and FunctionsRemote ControlButtons with no explanation function in the same way as the corresponding buttons on the projector's contr

6Part names and FunctionsRearBase••••[InputB] port Setup GuideConnects to the RGB port of a computer.••••[InputA] port Setup GuideConnects to the comp

7AppearanceCentre of projectorCentre of lens*1 Distance from centre of lens to suspension bracket fixing point(Lens shift amount: Max. 8.7 mm upwards,